
Seattle · Bellevue · Kirkland · Redmond
What we do
Fixed panels · hinged and pivot doors · door and panel · corner and neo-angle · steam enclosures · sliding and bypass doors · tub screens
We install frameless and semi-frameless shower glass: single doors, door-and-panel combinations, corner and neo-angle enclosures, steam enclosures, sliding doors and tub screens. Every piece is tempered safety glass, made to measure after the tile is finished, so it fits the real walls and curb instead of the drawing.
Below are the most common configurations. Not sure which one fits your bathroom? Send us a photo and rough dimensions, and we will tell you what works and what it takes.

One fixed glass panel and no door: you walk in around the end of the glass. It is the simplest and most open option, with nothing to open or adjust and very little to clean. It works best for walk-in and curbless showers that are deep enough to keep the spray inside. The panel is held by clamps or a floor channel and braced to the wall with a support bar.

A single frameless door on hinges mounted to the wall, opening outward into the bathroom. The classic choice for an alcove shower with three tiled walls. It needs clear floor space to swing, and the hinges need solid backing behind the tile to carry the weight of heavy glass.

A fixed panel and a door in the same opening, for showers too wide for a single door. The door can hang on the wall or on the panel itself with glass-to-glass hinges, and it can be placed on either side, usually away from the shower head so you can turn the water on without getting wet.

Two glass sides meeting at 90 degrees: a front with a door and panel, plus a return panel on the side. Used where the shower sits in a corner with only two tiled walls. Because two sides are glass, the whole bathroom looks larger and the tile stays on display.

Three pieces of glass across a corner: two short panels and a door set on the diagonal. The angled front takes less floor space than a square corner, which makes it a good fit for smaller bathrooms. The curb and shower pan are built to the same angled footprint, so it is easiest to plan together with the shower itself.

Glass runs all the way to the ceiling so the steam stays inside, with seals along the door edges and an operable transom at the top to let steam out after use. The glass is only one part of a steam shower: the walls and ceiling need a vapor-tight waterproofing system, the ceiling should be sloped so condensation runs down the walls, and the steam generator has to be planned in advance.

A heavy glass door that rolls on exposed rollers along a round or square rail, in front of a fixed panel. Nothing swings into the room, so it suits bathrooms where a hinged door would hit the toilet or vanity, while still looking modern and open.

Two glass panels that slide past each other on top and bottom tracks, so you can enter from either end. The usual choice for a tub-shower combination, and a practical option for long, narrow showers.

A single fixed or hinged half panel on the edge of the tub. It keeps spray off the floor when you shower while leaving the tub open and easy to reach, for example when bathing children.

Instead of hinges on the side, the door turns on pins at the top and bottom, set in from the edge. It can open both in and out, and it is useful where the wall next to the opening cannot carry hinges.
Shower glass sits on the curb and is anchored to the tiled walls, so it is only as good as the shower under it. When we build the shower too, the glass is part of the plan from the start: the curb top sloped toward the inside, solid backing in the walls where hinges and clamps will go, niches and tile lines kept clear of the hardware, and curbless floors sloped so water stays behind a fixed panel.
Once the tile is finished we measure the opening, the glass is made to those measurements, and then it is installed and sealed. If your shower is already finished and you only need new glass, we can measure and install that as well. See a recent shower with a frameless door and panel or request an estimate. Serving Seattle, Bellevue, Kirkland, Redmond and Tacoma.
Let's talk about your project
Tell us about the room you want to change. We visit, measure and send a detailed fixed-price proposal.